A timber roof truss is a structural framework of timbers designed to bridge the space above a room and to provide support for a roof. Trusses usually occur at regular intervals, linked by longitudinal timbers such as purlins. The space between each truss is known as a bay.
Timber roof trusses were a medieval development. Earlier roofs had been supported by coupled rafters - pairs of rafters linked by horizontal beams. But such roofs were structurally weak, and lacking any longitudinal support were prone to racking, a collapse resulting from horizontal movement.
Video Timber roof truss
History
The top members of a truss are known generically as the top chord, bottom members as the bottom chord, and the interior members as webs. In historic carpentry the top chords are often called rafters, and the bottom chord is often referred to as a tie beam. There are two main types of timber roof trusses: closed, in which the bottom chord is horizontal and at the foot of the truss, and open, in which the bottom chords are raised to provide more open space, also known as raised bottom chord trusses.
Maps Timber roof truss
Closed trusses
The terms closed truss and open truss are used in two ways to describe characteristics of truss roofs. Closed truss: 1) A truss with a tie beam; 2) a roof system with a ceiling so the framing is not visible. Open truss: 1) A truss with an interrupted tie beam or scissor truss which allow a vaulted ceiling area; 2) Roof framing open to view, not hidden by a ceiling.
King post truss
A king post truss has two principal rafters, a tie beam, and a central vertical king post. The simplest of trusses, it is commonly used in conjunction with two angled struts.
The king post is normally under tension, and requires quite sophisticated joints with the tie beam and principal rafters. In a variation known as a king bolt (rod) truss the king post is replaced by a metal bolt (rod), usually of wrought iron.
Queen post truss
A queen post truss has two principal rafters and two vertical queen posts. The queen post truss extends the span, and combined with spliced joints in the longer members extends the useful span for trusses of these types. As with a king post, the queen posts may be replaced with iron rods and thus called a queen rod truss. This truss is often known as a palladiana (Palladian truss) in Italy, as it was frequently used by the Venetian architect Andrea Palladio. Sometimes a palladian truss is defined as a compound truss with a queen post and king post truss in the same assembly.
The queen post truss and the king post truss may be combined, by using the straining beam of the queen post truss as the tie beam for a king post truss above. Such combinations are known as compound trusses.
Liegender Stuhl
Liegender Stuhl is a truss of German origin, the German name is used in America. This truss is found in some 18th and 19th-century buildings where Germans settled in the U.S. The literal translation is "lying chair", lying meaning the top chords are angled or leaning (and chair in the sense of a support, in this case a post or truss). Carpenters in the Netherlands also used this truss where it is spelled liggende stoel.
The opposite being a "Stehender Stuhl", which is the common roof truss type where simple vertical posts replace the more elaborate support structure in the image (highlighted in blue).
Open trusses
Arch-braced truss
Lacking a tie beam, the arch-braced (arched brace) truss gives a more open look to the interior of the roof. The principal rafters are linked by a collar beam supported by a pair of arch braces, which stiffen the structure and help to transmit the weight of the roof down through the principal rafters to the supporting wall. A double arch braced truss has a second pair of arched braces lower down, from the rafter to a block or inner sill: This form is called a wagon, cradle, barrel or tunnel roof because of this cylindrical appearance.
Hammerbeam truss
The hammerbeam roof was the culmination of the development of the arch-braced truss, allowing greater spaces to be spanned. The hammerbeam roof of Westminster Hall in London, designed by Hugh Herland and installed between 1395 and 1399, was the largest timber-roofed space in medieval Europe, spanning a distance of just over 20 metres (66 ft). It is considered to be the best example of a hammer-beam truss in England.
Hammer beam trusses can have a single hammerbeam or multiple hammerbeams. A false hammerbeam roof (truss) has two definitions: 1) There is no hammer post on the hammer beam as sometimes found in a type of arch brace truss or; 2)The hammer beam joins into the hammer post instead of the hammer post landing on the hammer beam.
Scissor truss
The scissor truss gets its name from being shaped like a pair of shears (scissors). Two defining features of a scissor truss are: 1) the joint where the bottom chords pass (the hinge of a pair of scissors) must be firmly connected and 2) the rafter (top chord) feet must land on the bottom chords. If the bottom chords join to the under-side of the top chords the assembly is said to be "scissor braced" rather than a scissor truss.
Bracing
It has been proven that permanent bracing designs can improve the lateral stability of roof trusses, specifically with j chords. Continuous lateral braces can prevent negative effects of lateral forces by being diagonally set in to brace the chord. However, there are variable effects of permanent braces on the truss web, given that the length of the chord would determine the number of brace locations.
Pre-fabricated wood trusses
Pre-fabricated wood trusses offer advantages in building construction through machine-made accuracy and tend to use less timber. However, this does not take into account site-specific design alterations that require customized truss design.
Historic wood trusses
The challenges of maintaining wood trusses are not limited to newer building projects. Visual grading can be used to conduct condition assessments for historic trusses. This along with load carrying tests, can be used to determine the best possible solutions to repairing older truss systems. Metal plates and correct, period material can be used to repair, although 100% recovery of the material may be hard if the wood truss has deteriorated. MPC wood trusses are typically made from lumber, rather than timber.
Connections in wooden trusses
The earliest wooden truss connections consisted of mortise-and-tenon joints and were most likely crafted at the construction site with the posts. Since most early trusses were made from unseasoned posts, the subsequent shrinkage would create cracking at the mortise-and-tenon joints. Additionally, the mortise-and-tenon joints in older trusses were located at the weakest point in the post, accelerating failure. Much of the early truss connection designs anticipated structural behaviour under loads. This is why holes were drilled slightly off-centre, allowing the peg to naturally pull the posts together with gravity.
See also
- Bent (structural)
- Reciprocal frame
- Timber framing
- Truss bridge
References
Notes
Citations
Bibliography
- Harris, Richard (2003), Discovering Timber-framed Buildings, Shire Publications, ISBN 978-0-7478-0215-0
- Steane, John (1984), Archaeology of Mediaeval England and Wales, Croom Helm, ISBN 978-0-7099-2385-5
- Yeomans, David T. (2003), The Repair of Historic Timber Structures, Thomas Telford, ISBN 978-0-7277-3213-2
External links
- Illustrated roof glossary
Source of article : Wikipedia
0 Comments